Go

 

  
Curtain RodsBlindsBamboo BlindsFalse ceiling Tee Grid

 
 

Metacil Aluminium / Steel Lineal Ceiling system is a unique system manufactured from Aluminium / Steel alloy sheet material. We have wide-ranging applications in the field of modern architecture. The ceiling system (both interior and exterior) are ideal for Hospitals, Restaurants, Hotels, Exhibition Halls, Petrol Pumps, Offices, Showrooms, Laboratories, Computer centers etc.

Lineal ceiling systems have a combination of both high strength and corrosion resistance with the least maintenance cost. The Ceilings are coated in standard shades with the best quality powder coated paint accepted internationally for ceiling applications. This protective coating can be applied after the manufacture or before by coil coating.
 

The fitting of individual panels is done with the help of suitable carriers and other allied accessories clamped together for achieving proper fitment. Standard light fittings, AC diffusers etc. can be built into the ceiling as per specific requirement to suit various designs, decors and tastes.
 
 
 
 

The Metacil Lineal Ceiling System comes complete with it’s Suspension System and accessories. These include Panel Carrier, Carrier Splice, Wall Angle, Panel Splice, Rod Hanger, Suspension Clip, Ceiling Cleat

These accessories can be made in the same combination as the panels for metal used in their construction and surface coating.

 
 
 
   
           
 

Metacil 84 C /184 C ceiling system comprises of 84 /184 mm x 12.5 mm panels with 23.9 mm flange roll formed out of metal coils. Panels are fixed on to roll formed carriers 32 mm wide x 39 mm deep out of 0.9/0.7 mm Aluminium or 0.5 mm galvanised steel sheet with cutouts to hold the panels in module of 100 / 200 mm at maximum 1.6 m c/c without insulation and at maximum 1.5 m c/c with insulation. Carriers are suspended from the roof or truss by 4 mm dia. galvanized steel wire rod hanger with special height adjustment suspension clip at max. 1.3 m c/c. Hangers are fixed to the roof by ‘J’ hooks and nylon inserts. Panels are factory cut in lengths up to maximum 6 m to suit site dimensions or shop drawings. Edge profiles or wall angles are 24 mm X 24 mm X 0.5 mm thick and match the colour of the panel.

These systems have several options for the metal used in their construction, the protective coating used on the surfaces and the finish of the panels. These are as follows:

Metal used for construction of both panels and grid:

Aluminium - Alloy AA5050, AA3105 or AA1050 is used to make the panels and the grid. These alloys are standard as per American Society for Testing and Materials (ASTM). For example, the standard for Alloy AA5050 is given in the table below. Thickness is 0.5 mm for panels and 0.8/0.9 mm for grid.

Mild Steel - Galvanised with 180 / 120 gsm Zinc coating, 240 Mpa yield stress. Thickness is 0.5 mm for panels and 0.6 mm for grid. Panels can also be made from 0.45 mm thick sheets.

Protective coating used on the surface of both panels and grid:

Uncoated - Galvanised with 180 gsm Zinc coating, 240 Mpa yield stress.

Powder coated - 50 micron polyester after pretreatment.

Coil coated – The surface is chromatised and stove enameled on both sides in the manufacturer’s standard colour shades. The panels have coil coating finish on the face. The top coat of the panel has 20 micron polyester coated finish and back has a coat of 5 micron alkyd primer.

Finish of the panels:

·Plain

Perforated – With holes of 2 mm dia. at 5 mm c/c. (standard) staggered in uniform pattern and symmetrically located in the middle of the panel face. The panels have non-woven tissue over the ceiling for improved acoustics.

·Micro perforated – As above but with holes of 1 mm dia 
 
          
 

Metacil 84R ceiling system comprises of 84 mm x 16 mm panels without flush profile and Metacil 84 F ceiling system comprises of 84 mm x 16 mm panels with flush profile of the same metal (for 100 mm module only) roll formed out of metal coils. Panels are fixed on to roll formed carriers 32 mm wide x 39 mm deep made out of 0.9/0.7 mm Aluminium or 0.5 mm galvanised steel sheet with cutouts to hold the panels in module of 100 mm at maximum 1.7 m c/c without insulation and at maximum 1.5 m c/c with insulation. Carriers are suspended from the roof or truss by 4 mm dia. galvanized steel wire rod hanger with special height adjustment suspension clip at max. 1.3 m c/c. Hangers are fixed to the roof by ‘J’ hooks and nylon inserts. Panels are factory cut in lengths up to maximum 6 m to suit site dimensions or shop drawings. Edge profiles or wall angles are 24 mm X 24 mm X 0.5 mm thick and match the colour of the panel.

These systems have several options for the metal used in their construction, the protective coating used on the surfaces and the finish of the panels. These are as follows:

Metal used for construction of both panels and grid:

Aluminium - Alloy AA5050, AA3105 or AA1050 is used to make the panels and the grid. These alloys are standard as per American Society for Testing and Materials (ASTM). For example, the standard for Alloy AA5050 is given in the table below. Thickness is 0.5 mm for panels and 0.9/0.7 mm for grid.

Mild Steel - Galvanised with 180 / 120 gsm Zinc coating, 240 Mpa yield stress. Thickness is 0.5 mm for panels and 0.5 mm for grid. Panels can also be made from 0.45 mm thick sheets.

Protective coating used on the surface of both panels and grid:

Uncoated - Galvanised with 180 gsm Zinc coating, 240 Mpa yield stress.

Powder coated - 50 micron polyester after pretreatment.

Coil coated – The surface is chromatised and stove enameled on both sides in the manufacturer’s standard colour shades. The panels have coil coating finish on the face. The top coat of the panel has 20 micron polyester coated finish and back has a coat of 5 micron alkyd primer.

Finish of the panels:

Plain

Perforated – With holes of 2 mm dia. at 5 mm c/c. (standard) staggered in uniform pattern and symmetrically located in the middle of the panel face. The panels have non-woven tissue over the ceiling for improved acoustics.

Micro perforated – As above but with holes of 1 mm dia.
 
 

 

Metacil 150F ceiling system comprises of 150 mm X 17 (+/-10%) mm panels roll formed out of metal coils. Panels are fixed on to roll formed carriers 34.5 mm wide X 48 mm deep out of 0.9/0.7 mm Aluminium or 0.5 mm galvanised steel with cutouts / prongs to hold the panels in module of 150 mm at maximum 1.7 m c/c without insulation and at maximum 1.5 m c/c with insulation. Carriers are suspended from the roof or truss by 4 mm dia. galvanized steel wire rod hanger with special height adjustment suspension clip at max. 1.3 m c/c. Hangers are fixed to the roof by ‘J’ hooks and nylon inserts. Panels are factory cut in lengths up to maximum 6 m to suit site dimensions or shop drawings. Edge profiles or wall angles are 25 mm X 25 mm X 0.5 mm thick and match the colour of the panel

These systems have several options for the metal used in their construction, the protective coating used on the surfaces and the finish of the panels. These are as follows:

Metal used for construction of both panels and grid:

Aluminium - Alloy AA5050, AA3105 or AA1050 is used to make the panels and the grid. These alloys are standard as per American Society for Testing and Materials (ASTM). For example, the standard for Alloy AA5050 is given in the table below. Thickness is 0.5/0.6 mm for panels and 0.9 mm for grid.

·Mild Steel - Galvanised with 180 / 120 gsm Zinc coating, 240 Mpa yield stress. Thickness is 0.5/0.6 mm for panels and 0.6 mm for grid.

§Protective coating used on the surface of both panels and grid:

·Uncoated - Galvanised with 180 gsm Zinc coating, 240 Mpa yield stress.

·Powder coated - 50 micron polyester after pretreatment.

·Coil coated – The surface is chromatised and stove enameled on both sides in the manufacturer’s standard colour shades. The panels have coil coating finish on the face. The top coat of the panel has 20 micron polyester coated finish and back has a coat of 5 micron alky primer.

Finish of the panels:

·Plain

·Perforated – With holes of 2 mm dia. at 5 mm c/c. (standard) staggered in uniform pattern and symmetrically located in the middle of the panel face. The panels have non-woven tissue over the ceiling for improved acoustics.

·Micro perforated – As above but with holes of 1 mm dia.
 
 

Metacil 75C / 100C / 150C ceiling systems comprises of panels 75 mm / 100 mm / 150 mm wide x 15.5 mm deep with beveled groove between panels formed out of metal coils. Panels are fixed on to roll formed carriers 32 mm wide x 39 mm deep out of 0.9/0.7 mm Aluminium or 0.5 mm galvanised steel with cutouts to hold the panels in module of 100 mm at maximum 1.6 m c/c without insulation and at maximum 1.5 m c/c with insulation. Carriers are suspended from the roof or truss by 4 mm dia. galvanized steel wire rod hanger with special height adjustment suspension clip at max. 1.3 m c/c. Hangers are fixed to the roof by ‘J’ hooks and nylon inserts. Panels are factory cut in lengths up to maximum 6 m to suit site dimensions or shop drawings. Edge profiles or wall angles are 24 mm X 24 mm X 0.5 mm thick and match the colour of panel. 

These systems have several options for the metal used in their construction, the protective coating used on the surfaces and the finish of the panels. These are as follows:

 Metal used for construction of both panels and grid:

·Aluminium - Alloy AA5050, AA3105 or AA1050 is used to make the panels and the grid. These alloys are standard as per American Society for Testing and Materials (ASTM). For example, the standard for Alloy AA5050 is given in the table below. Thickness is 0.5 mm for panels and 0.9/0.7 mm for grid.

·Mild Steel - Galvanised with 180 / 120 gsm Zinc coating, 240 Mpa yield stress. Thickness is 0.5 mm for panels and 0.6 mm for grid. Panels can also be made from 0.45 mm thick sheets.

§Protective coating used on the surface of both panels and grid:

·Uncoated - Galvanised with 180 gsm Zinc coating, 240 Mpa yield stress.

·Powder coated - 50 micron polyester after pretreatment.

·Coil coated – The surface is chromatised and stove enameled on both sides in the manufacturer’s standard colour shades. The panels have coil coating finish on the face. The top coat of the panel has 20 micron polyester coated finish and back has a coat of 5 micron alkyd primer.

Finish of the panels:

·Plain

·Perforated – With holes of 2 mm dia. at 5 mm c/c. (standard) staggered in uniform pattern and symmetrically located in the middle of the panel face. The panels have non-woven tissue over the ceiling for improved acoustics